Automotive Manual PDF

RSS Feed

The Resources for Automotive

How do you replace a turn signal thermal flasher unit?

December 27th, 2010 · No Comments

I have a 1992 Cadillac Sedan DeVille. The turn signals have stopped functioning, and I believe the culprit to be an old Thermal Flasher Unit. I have found the unit, it is a Wagner 552, 12v. It has two wires coming off the back of the little aluminum can shaped thing.
How do I install a new one?
How do I take the old one out?! I can’t see where the wires go off to in the bundle, and I don’t know if you’re supposed to unplug the little aluminum can where the wires attach to the unit itself, or at the end of wherever those wires lead to in the bundle.
(more…)

[Read more →]

1998-2000 Chevrolet S10 Blazer Sportsman Assemblies Installation Instructions

October 20th, 2009 · No Comments

Remove the contents from the box and check for any damage. Verify all parts against the parts list.
Read and understand instructions completely before beginning installation.
Remove 10mm bolts from bumper brace located on back side of front body mount if present. For each side, place Mount Bracket up to the backside of the body mount and secure using existing 10mm bolts removed in step 3. (On trucks without existing bolts, use the 10mm hardware provided in the bolt kit).
(more…)

[Read more →]

2004 Ford E-350 Series Van 400-series Lighthead Housing Installation Guide

March 25th, 2009 · No Comments

Installation:
1. Following the vehicle manufacturers instructions, remove the radiator shroud, grill, headlights and turn signals. Then remove the plastic substructure that they are mounted to (Fig. 1).
2. While holding the housing (without lighthead) in the exact mounting location, mark the location of the two mounting holes onto the mounting surface. There is a small notch cut into the inside of the two screw bosses on the housing. Use the notch as a guide, make your mark, then (with the housing removed) measure and make the mounting holes 5-3/8” apart (Figs. 2 & 3). NOTE: Depending on what lighthead you are using with this housing, you will need to drill a wire hole. Refer to the lighthead manual for the size and location.
(more…)

[Read more →]

Ducati Monster Bobbed License Plate / Signal Relocation Bracket – Redpoint Racing

January 26th, 2009 · No Comments

The relocation bracket is designed to fit all Ducati Monsters within the year ranges of 2000-2004. It may fit other years as well, but I cannot guarantee an exact fit as minor changes have been done throughout the years. The bracket is designed to replace the stock tail light/turn signal/license plate assembly and the rearmost section of the frame on which the stock assembly mounts. It is assumed that the sub frame has already been removed.
(more…)

[Read more →]

2002 Mercedes Benz C 32 AMG (203.065) V6-3.2L SC – Lighting – Front Turn Signals Inoperative

July 6th, 2008 · No Comments

If you encounter instances in Model 203 vehicles of the front turn signal not working, this may be due to a contact problem between the turn signal bulb socket and the headlamp housing. In this case, perform the following repair only on the affected side of the vehicle.
(more…)

[Read more →]

Audi A4/A4 Avant Quick reference guide pdf

March 7th, 2008 · No Comments

The central locking system locks and unlocks all the doors, the boot lid and the tank flap. It can be operated with the remote control or by turning the key in the lock. Remote control keys Press the appropriate button for about 1 second. e Unlocking button: Open one of the doors within about 60 seconds, otherwise the vehicle will lock itself again automatically. r Unlocking button for boot lid: Press the button for at least 1 second. t Locking button: The turn signals flash once to confirm that the doors and boot lid are properly closed and locked. u Folding out the master key: Press the release button. Folding in the master key: Press the button and fold in the key.
(more…)

[Read more →]

Audi A6/A6 Avant Quick Reference Guide pdf

March 7th, 2008 · No Comments

Audi A6 Service Manual: 1998-2004 pdf Remote control keys Press the required button. e Unlocking button: Open one of the doors within about 60 seconds, otherwise the vehicle will lock itself again automatically. r Unlocking button for boot lid/tailgate: Press the button for at least 1 second. t Locking button: The turn signals flash once to confirm that the doors and boot lid/tailgate are properly closed and locked.u Folding out the master key: Press the release button. Folding in the master key: Press the button and fold in the key.
(more…)

[Read more →]

Tips for Honda CBR 600 F4I/RR Flushmount signal installation

March 2nd, 2008 · No Comments

In order to remover the factory turn signals and install ours, you will need to remove the entire upper fairing. 2.) Remove the original turn signals from the upper fairing. You can cut the connector off the factory turn signals and splice it into the G.C. turn signals. Simply place the G.C. signals into the spot on the fairing left vacant by the factory signals. The wires will go through the large hole in the fairing and the screw will attach through the small hole.
(more…)

[Read more →]