Automotive Manual PDF

Headlamp guard
Installation
1 - Open the bonnet
- Clean the headlamp lens
- Take the mounting strips for the headlamp guards from the kit
- Pry up the weatherstrip for the headlamp. Use a plastic weatherstrip tool
- Insert the mounting strip between the top of the headlamp and the weatherstrip. Position the mounting strip as illustrated. (more…)

[Read more →]

This workshop manual contains technical specification, descriptions and instructions for repairing the standard versions of the following engines TAMD31M, TAMD31L, TAMD31P, AD31L, AD31P, KAD32P, TAMD41H, TAMD41M, TAMD41P, AD41P, TAMD42WJ, KAMD42A, KAMD42B, KAMD42P, KAD42A, KAD42B, KAD42P, KAMD43P, KAD43P, KAMD44P, KAD44P. The workshop manual displays the operations carried out on any of the engines above. As a result the illustrations and pictures in the manual that show certain parts on the engines, do not in some cases apply to all the engines listed above. However the repair and service operations described are the same in all essential details.
(more…)

[Read more →]

The BC-harness is delivered complete with all the connectors. When all the wiring is complete it’s important to secure the harness and make sure that it’s not mounted directly on top of extremely hot engine parts such as the header. You can use cable ties to secure the harness.
(more…)

[Read more →]

System is equipped with a cycling clutch system that uses an expansion valve in refrigerant line between condenser and evaporator, near condenser. System is engaged when A/C switch on control panel is pressed. See Fig. 1. Pressure switch on accumulator cycles compressor clutch on and off. Blower fan speed is controlled by sliding switch on lower left of A/C-heater control panel.
(more…)

[Read more →]

Tools required:
1. Flathead screwdriver.
2. Electrical crimper/cutter.
3. Fine needlenose pliers or c-clip remover (or even something with a pointy tip)
4. 4mm or 5/32” hex key, ideally a 3/8” driver style. A similar size of torx will do in a pinch. Driver extensions are very handy.
5. 8mm and 10mm socket driver.
6. Work light!
(more…)

[Read more →]

This is an install document for a High Intensity Discharge Kit for the Volvo S40. This is a fairly simple procedure and should take approximately 45 minutes to install.
Kit Details
DDM HID Kit including:
2 – Ballasts and Igniter assemblies
2 – HID Bulbs w/wire assemblies
2 – Ballast to Bulb connecting wires
2 – 3M Double sided adhesive tape
(more…)

[Read more →]

This Service Light & Airbag Reset Tool is an essential tool for resetting of oil service light, service warning light, service mileage, service intervals and airbag on European made vehicles like AUDI, BMW, CITROEN, M. BENZ,MINI, SAAB, SEAT, SKODA,VOLKSWAGEN, VOLVO, etc.
(more…)

[Read more →]

The warning lights described on this page should never be on when driving. When the ignition is turned on, and before the engine starts, all of the warning lights should be on to test the function of the bulbs. Should a light not go off after the engine has started, the system indicated should be inspected. (However, the parking brake reminder light will not go off until the parking brake is fully released.)
(more…)

[Read more →]

When your car is parked, the gear selector is locked in the (P)ark position. To release the selector from this position, turn the ignition key to position II (or start the engine), depress the brake pedal, press the button on the top of the gear selector and move the selector from (P)ark. If it is necessary to manually override the Shiftlock system, see page 107 for instructions.
(more…)

[Read more →]

This Owner’s manual provides information on driving and maintaining your Volvo
It should be noted that there are certain differences among model versions and market requirements; thus, you may find features described and/or pictured in this manual that do not appear on your car. Should you require more detailed information with regard to adjustments or repairs please contact your Volvo dealer.
(more…)

[Read more →]